Showing results: 16 - 30 of 35 items found.
-
LSP -
inTEST Corporation
The LSP mounts to standard prober hinge mounts with easy access to service and engineering locations. This reduces the floor space per test cell, saving you significant capital expenses. And you’ll be able to quickly and easily set up your ATE to wafer probe.
-
4605-HTR -
TESEC, INC
4605-HTR is a MAP Sorter which picks up devices from wafer ring and sorts to tape or bin according to the MAP file created by film frame test handler or prober. 4605-HTR is a high speed handling system, available for 12 inches wafer rings. When used in combination with 4170-IH, 4605-HTR much improves efficiency in testing process of leadless devices as a high speed sorting machine.
-
TestEdge, Inc.
TestEdge offers complete wafer sort solutions. Our range of wafer sort capabilities demonstrates our ability to handle a wide range of devices and device characteristics. State of the art Electroglas probers Sort experience with high probe count Less than 4 mil pitch on probes Experience with C4 Bump and Aluminum pad Experience on Bipolar, CMOS, GaAs, & SiGe Overhead sort or cable harness sort Microsite testing capability
-
T5230 -
Advantest Corp.
T5230 memory test system for NAND/NVM devices adopts a combined array architecture to achieve best-in-class cost-of-test performance for wafer test, including wafer-level burn-in (WLBI) and built-in self-test (BIST). The system can perform on-wafer test of 1,024 memory devices per test head in parallel, delivering high productivity and enabling floor space savings of up to 86%. Multiple test cells are connected per system controller in the T5230, allowing independent wafer test of each test cell. The test cells can be stored in a general multi-wafer prober while minimizing the test cell floor space, and the tester can be docked with probers in both linear and multi-stack configurations. For functional tests at a maximum test rate of 125MHz/250Mbps, the T5230 assures high timing accuracy, repeatability, and failure detection capability.
-
Keysight Technologies
Conducting all the parametric measurements necessary for the numerous test structures on a semiconductor wafer can be a time-consuming and expensive process. With the cost of end-user devices continuing to drop, even laboratory characterization environments must reduce the cost of test. Until now engineers and scientists working on current and future semiconductor process technologies were faced with a difficult choice: either use a semiconductor parameter analyzer with positioners on a wafer prober, which limits the ability to perform automated test, or use a switching matrix and probe card, which reduced the analyzer's measurement resolution. Utilizing a switching matrix with a semi-automatic or fully-automatic wafer prober enables characterization tests to be automated, eliminating the need to have an operator manually reposition the probes each time a new module needs to be tested. This reduces both test time and cost. Due to the many price/performance points available, Keysight's switching matrix solutions provide the flexibility to choose exactly what your testing needs require, without overspending.
-
Keysight Technologies
WaferPro Express software performs automated wafer-level measurements of semiconductor devices such as transistors and circuit components. It provides turnkey drivers and test routines for a variety of instruments and wafer probers. Its new user interface makes it easy to setup and run complex wafer-level test plans, while powerful customization capabilities are enabled by the new Python programming environment.
-
FOX-1P -
Aehr Test Systems
Enables High Throughput, Single Touchdown, Full Wafer Production Testing. Capable of simultaneously testing up to 16,000 die in a single wafer touchdown. Resource configurable up to 16,384 " Universal Channels " - each programmable as anI/O, Clock, Pin Parametric Measurement Unit ( PPMU ) or Device Power Supply ( DPS ). Software-enabled per site flexibility to support small and large device pin count test needs. Comprehensive functional and parametric test capabilities Deep functional pattern data and capture memory optimized for BIST/DFT testing. Per channel PMU for per site parametric testing Individual channel over-current protection to protect wafers and probe cards. Configured for high volume production. Compatible with industry standard probers and probe cards. Available as an integrated test cell with prober, probe cards and 16,384 channel probe I/F. Configurable as a single or dual system integrated test cell.
-
Keysight Technologies
Keysight EasyEXPERT group+ GUI based characterization software is available for Keysight Precision Current-Voltage Analyzer Series. It is available on your PC or the B150xA's embedded Windows 7 platform with 15-inch touch screen to accelerate the characterization tasks. It supports efficient and repeatable device characterization in the entire characterization process from measurement setup and execution to analysis and data management either interactive manual operation or automation across a wafer in conjunction with a semiautomatic wafer prober. EasyEXPERT group+ makes it easy to perform complex device characterization immediately with the ready-to-use measurements (application tests) furnished, and allows you the option of storing test condition and measurement data automatically after each measurement in a unique built-in database (workspace), ensuring that valuable information is not lost and that measurements can be repeated at a later date. Keysight Precision Current-Voltage Analyzer Series provides the complete solution for device characterization with these versatile capabilities.
-
Keysight Technologies
Keysight Easy EXPERT group+ GUI based characterization software is available for Keysight Precision Current-Voltage Analyzer Series. It is available on your PC or the B150xA's embedded Windows 7 platform with 15-inch touch screen to accelerate the characterization tasks. It supports efficient and repeatable device characterization in the entire characterization process from measurement setup and execution to analysis and data management either interactive manual operation or automation across a wafer in conjunction with a semiautomatic wafer prober. EasyEXPERT group+ makes it easy to perform complex device characterization immediately with the ready-to-use measurements (application tests) furnished, and allows you the option of storing test condition and measurement data automatically after each measurement in a unique built-in database (workspace), ensuring that valuable information is not lost and that measurements can be repeated at a later date. Keysight Precision Current-Voltage Analyzer Series provides the complete solution for device characterization with these versatile capabilities.
-
Dynamic Test Solutions
DTS has a full line of standard PIBs for all major tester platforms. Custom PIB designs can accommodate any test head, prober and manipulator configuration, including probe card changers, overhead direct dock setups and cable interfaces. DTS wafer test loadboards are compatible with a variety of pogo pin interface towers. All PIBs are constructed with impedance control, precision matched line lengths, full power and ground planes and both analog and digital resources to provide high quality signal integrity directly to the device.
-
Keysight Technologies
Accurate DC/CV (and RF) statistical modeling of semiconductor devices requires collecting a significant amount of measured data from different wafers across several temperatures. Keysight Technologies recommends IC-CAP WaferPro as a turn-key DC/CV and RF automated characterization solution to help modeling and device engineers achieve more efficient on-wafer measurements across temperature. This new breakthrough solution is based on IC-CAP modeling software and efficiently controls DC/CV analyzers, network analyzers, probers, switching matrixes, and temperature chucks, as well as the powerful 407x and 408x Series of Keysight parametric testers.
-
TLP-3010C -
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±8 kV*High pulse output current up to ±30 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
TLP-4010C -
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
EasyEXPERT group+ -
Keysight Technologies
Keysight EasyEXPERT group+ GUI based characterization software is available for Keysight Precision Current-Voltage Analyzer Series. It is available on your PC or the B150xA's embedded Windows 7 platform with 15-inch touch screen to accelerate the characterization tasks. It supports efficient and repeatable device characterization in the entire characterization process from measurement setup and execution to analysis and data management either interactive manual operation or automation across a wafer in conjunction with a semiautomatic wafer prober. EasyEXPERT group+ makes it easy to perform complex device characterization immediately with the ready-to-use measurements (application tests) furnished, and allows you the option of storing test condition and measurement data automatically after each measurement in a unique built-in database (workspace), ensuring that valuable information is not lost and that measurements can be repeated at a later date. Keysight Precision Current-Voltage Analyzer Series provides the complete solution for device characterization with these versatile capabilities EasyEXPERT group+ is upgradable from the previous generation of EasyEXPERT/Desktop EasyEXPERT software.
-
TLP-8010A -
High Power Pulse Instruments GmbH
*Wafer and package level TLP/HMM testing*Fast 50 Ω high voltage pulse output with typical 300 ps rise time*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω-configuration*High pulse output current up to ±80 A (short circuit) with 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 300 ps to 50 ns*1 built-in pulse width: 100 ns*Optional external pulse width extensions 5/10/50/100/200/500 ns using an external pulse width extender TLP-8012A5*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurements of complete wafers*High performance and high quality components
